How to Build and Install a Fence

DIY approaches are now becoming more popular, especially that there are many tutorial videos and articles that you can base. One of these DIY projects that you successfully do is fence installation Kansas City. Just follow this tutorial we made for you, and you’re good to go.  


Step 1:  

The first thing to do is marking the layout. Use batter boards and string for this. Put the batter boards beyond the location where you plan to out the fence corners. Run the strings, this will help you line up the posts later.  

Step 2: 

Use your marking paint and stakes to mark the posts and the spacing. The traditional space is 6 to 8 feet from one post’s center to the next posts. Make sure that the tape measure is level so you can have accurate spacing. The strings mark the post’s outside faces.  

Step 3: 

Once you establish the location of the post holes, use a pencil and mark the position of the strings on the batter boards. The batter boards near the house should be transferred just in case you will remove it later for digging. Remove the strings so you can dig the holes easily.  

Step 4:  

This is the time when you dig the holes to sizes. Check the building codes; some might require you to dig below the frost line to prevent the post from being pushed up while freezing. The diameter of the post hole is typically three times the post’s width. Use the marks you made on the batter boards to reset the layout lines.  

Step 5:  

You now have your first hole; next thing to do is fill it with 6 inches of dry concrete mixture. Place one post over the dry concrete, avoid pushing it outward. Make sure that the post is plumb, use a level to check this. Next, add the braces so the post is held into its place. Do the same steps for the next posts. Once you’re done, put concrete mix on the post holes and let it cure. Remove the braces, take down the strings and batter boards.  

Step 6:  

This is the beginning of installing the fence. First, mark the location of the rail in the posts. Measure the bottom and top rail locations to determine the middle rail’s placement. Once you’re done with that, you can now install the rails. Measure and cut the rails, so they are on their best size. Trim the rail ends. Begin attaching the rest of the rails in the entire fence. Once you approach the end of the fence, cut the final rails.  

Step 7: 

It’s now time to install the fence pickets. The tops should be kept at a uniform height. Start at the corner, secure them with a pneumatic nailer. After installing the pickets on the outside, work on the inside of the fence.  

Step 8: 

Finally, you can now install the fence gate. Use your gate hardware kit to prevent it from sagging. After that, you can finish the fence with the necessary finishing.

Read More

The Amazing Benefits of Cool Pavements

Driving in a dark pavement is uncomfortable. It gets too hot under the sun because it absorbs 90% of the sunlight. When you have a road trip in hot summer day, the air is too hot to handle because the dark pavement which aggravate the urban heat island. Fortunately, cool pavements are invented to reflect the sunlight. If you hire South Florida pavers, you can always opt for a cool pavement.  

Cool Pavements

Cool pavements are made from cement concrete, which is a traditional material for paving. The new cement concrete has a solar reflectance of 50%, and the coating for asphalt concrete has reflectance of about 50% too. The solar reflectance of cement and asphalt pavements can change overtime. The asphalt pavement will lighten as it ages but the cement concrete gets darker with grease stains and tire.  

The following are the amazing benefits of cool pavements.  

Energy Savings and Emission Reductions 

Installing cool pavement will lower the air temperature outside. It doesn’t only benefit the drivers and commuters who have been suffering from too much heat; it also helps the building owner to cool their place without using too much energy. The cool pavements also save the energy used by the electric street lighting.  

Improved Health and Comfort 

Dark pavements make the heat situation worse, so a cool pavement is a relief when it comes to comfort. Such pavements cool the air temperature of the city, which reduces the illness we get because of heat. It also helps when it comes to slowing down the formation of smog, so people would be more comfortable going outside. When you’re out there driving in a hot summer day, you won’t experience that much heat.  

Increased Driver Safety 

Cool pavements doesn’t only increase your comfort, it also improves the safety of the driver. Pavements which are light-colored are better than the dark ones because it reflects street light and headlights especially during at night. The visibility is increased, so you’re safer when driving out there.  

Improved Air Quality 

The city life is busy. With all the buildings, restaurants and industrial companies, you can only imagine the condition of the air you breathe. Installing cool pavements in the community will decrease the air temperature in urban areas. It can slow down the atmospheric chemical reactions that create the smog.  

Reduced Street Lighting Cost 

Cool pavements don’t only reduce the hot air temperature; it also increases the solar reflectance of the roads. This way, the street lighting uses less electricity especially at night because it can reflect light well.  

Slowed Climate Change 

Like we mentioned, cool pavements have the ability to decrease the heat absorbed at the surface of the Earth. It lowers the temperature of the Earth’s surface, thus the surface temperature is also lowered. The decrease in such temperature has an effect on the climate change, which slows it down. The cool pavement also cools the storm water, which leads to lessen damage to local watersheds.

Read More